PCB's

Universal PCB, small

Enlarge

If you are unsure which PCB to use we recommend universal PCB's.

Epoxy glass fibre laminate PCB 150 x 115 mm with 35 um Cu layer.

Available with spacer: Order No. I-2754,    
Price   EUR 5,70

without accessories: Order No. I-8805017,    
Price   EUR 4,70
fitting connecting terminals for assembly, 10 mm grid, up to 4 mm² cable diameter:
2-pin, Order No. I-7207,     Price   EUR 1,00
4-pin, Order No. I-7208,     Price   EUR 1,95      
 

Universal PCB, large

Enlarge

Epoxy glass fibre laminate PCB 220 x 155 mm with 35 um Cu layer.

tin plated with spacer: Order No. I-2755,    
Price   EUR 10,80

tin plated, without accessories: Order No. I-8805002,    
Price   EUR 8,80
fitting connecting terminals for assembly, 10 mm grid, up to 4 mm² cable diameter:
2-pin,Order No. I-7207,     Price   EUR 1,00
4-pin, Order No. I-7208,     Price   EUR 1,95      
 

Grid PCB's

These PCB come in different sizes, however, all of them have a grid spacing of 5 mm.

Enlarge

RA140, 140 x 102 mm
Order No. I-2765,   Price   EUR 3,40

RA160, 159 x 127 mm
Order No. I-2766,   Price   EUR 5,10

RA 240, 240 x 165 mm
Order No. I-2767,   Price   EUR 7,60
 

PCB, small

Picture left: mounting side view (conductors are shining through)
Below left: terminals E+, E- for connection to the amplifier
Right: terminals for connection to the drivers

For connection of
- A bass driver with 44 mm diameter coil
- Capacitor 37.5 x 16 mm with resistor 5 Watt
- A tweeter with PTC resistor
- 3 capacitors
- 2 resistors
- 1 coil with 32 mm diameter

Order No. I-2763,    EUR 5,79

additionally connecting terminals for assembly,10 mm grid , up to 4 mm² cable diameter:
2-pin, Order No. I-7207,     Price   EUR 1,00
4-pin, Order No. I-7208,     Price   EUR 1,95       (one of each is needed)
 

PCB, large

The picture left shows 4 terminals to connect to the amplifier EH+,- ET+,- for bi-wiring.

Two of each may also be connected with one another.

To the right in the picture 4 outputs to the drivers H+,- and T+,- can be seen.

Order No. I-2762,    Price  EUR 9,69

additionally connecting terminals for assembly, 10 mm grid, up to 4 mm² cable diameter:
4-pin, Order No. I-7208,     Price   EUR 1,95       (two are needed)
 

Subwoofer PCB, large

Order No. I-2760,     Price   EUR 11,40

additionally connecting terminals for assembly, 10 mm grid, up to 4 mm² cable diameter:
2-pin, Order No. I-7207,     Price   EUR 1,00
4-pin, Order No. I-7208,     Price   EUR 1,95       (one each is needed)

 

Equalizer PCB

Epoxy glass fibre laminate PCB 120 x 85 mm with 35 um Cu layer, tin plated.

For connection of an equalisation system for impedance linearisation. The following component's fit on the PCB:
- 1 coil with 55 mm diameter
- 3 parallel capacitors of 52.5 x 25 mm and
- 2 parallel resistors 10 Watt

If just one RLC element is needed only terminals E+ and E- are required.

Order No. I-2761,     Price   - not available

additionally connecting terminals for assembly, 10 mm grid, up to 4 mm² cable diameter:
2-pin, Order No. I-7207,     Price   EUR 1,00       (depending on application 1 or 2 are required)
 

Monacor PCB's

Epoxy glass fibre laminate Epoxyd FR4 with 70 um tin plated conductor tracks. The wide tracks are suitable for high power application like PA or high-end (picture left: DNU-100).

Order No.	Size in cm	Application	Price
mo-DNU-400	27 x 17.5	3 way crossover etc.	- not available
mo-DNU-200	15 x 13	2 way crossover up to 12 dB	on request (_)
mo-DNU-100	12 x 11	2 way crossover up to 12 dB or 6 dB low pass & 18 dB high pass	on request (_)

Home